I have the cluster out and just replaced all the light bulbs, gonna change the lens while I am at it.
However, I have found that someone for some reason has spliced the two turn signal bulbs together, and then to a toggle switch mounted in the dash. I tested the turn signals before I started tearing down and they worked, both outside and inside. The only thing I can think of is a f'd up trailer wiring job, the splices are as crude as you can imagine.
So now I need to get these wire reconnected the right way. I have two bulbs, two wires, one from each socket, but only one cut wire from the harness. All wires are Blue/Red stripe. Thanks!
Guage cluster lights...
Moderators: FORDification, Thunderfoot
-
- Preferred User
- Posts: 315
- Joined: Thu Feb 08, 2007 11:34 pm
- Location: Texas, Waxahachie
Guage cluster lights...
You do not have the required permissions to view the files attached to this post.
- 71PA_Highboy
- Blue Oval Fanatic
- Posts: 923
- Joined: Tue May 23, 2006 11:32 am
- Location: Denver of the East
re: Guage cluster lights...
Blue w/red stripe is your dash light circuit, not turn signals.
Not sure how to advise you from there though.... are you sure they are in the turn signal holes?
regards,
eric
Not sure how to advise you from there though.... are you sure they are in the turn signal holes?
regards,
eric
Got Ford?
2 EarlyBroncos (68,69)
2 Classic Mustangs (69,70)
1 F250 4x4 (71) - OB - 360, NP435, D24, HPD60 4.10, D60,
1 94 Ranger, 2.3, 5spd
1 Lincoln Mark VIII
2 EarlyBroncos (68,69)
2 Classic Mustangs (69,70)
1 F250 4x4 (71) - OB - 360, NP435, D24, HPD60 4.10, D60,
1 94 Ranger, 2.3, 5spd
1 Lincoln Mark VIII
- Thunderfoot
- 100% FORDified!
- Posts: 2207
- Joined: Tue Apr 17, 2007 2:34 pm
- Location: Idaho, Boise
re: Guage cluster lights...
I agree with Eric,
The Blue - Red stripe is the dash lights…looking at this diagram http://www.fordification.com/images/sch ... s81-85.jpg the instrument panel has 19 and 19A they both are connected together and go into the plug as one wire…
Looking at this diagram http://www.fordification.com/images/sch ... ghts01.jpg the turn signal wires are; Left side= 50 (Green – white stripe) and Right side= 49 (White – blue stripe)
Hope this helps...
The Blue - Red stripe is the dash lights…looking at this diagram http://www.fordification.com/images/sch ... s81-85.jpg the instrument panel has 19 and 19A they both are connected together and go into the plug as one wire…
Looking at this diagram http://www.fordification.com/images/sch ... ghts01.jpg the turn signal wires are; Left side= 50 (Green – white stripe) and Right side= 49 (White – blue stripe)
Hope this helps...
Shayne
I'm not "Brand Loyal" Ford-Chevy-Dodge-Toyota I have them all, one even cross mixed...
If it Looks good and Works good then it's ok by me. Everything has its issues from time to time...
69 SWB (project) & 69 Highboy (driver/project)
http://s197.photobucket.com/albums/aa29 ... d%20truck/
http://www.fordification.com/galleries/ ... ?cat=10399
I'm not "Brand Loyal" Ford-Chevy-Dodge-Toyota I have them all, one even cross mixed...
If it Looks good and Works good then it's ok by me. Everything has its issues from time to time...
69 SWB (project) & 69 Highboy (driver/project)
http://s197.photobucket.com/albums/aa29 ... d%20truck/
http://www.fordification.com/galleries/ ... ?cat=10399
-
- Preferred User
- Posts: 315
- Joined: Thu Feb 08, 2007 11:34 pm
- Location: Texas, Waxahachie
-
- Preferred User
- Posts: 315
- Joined: Thu Feb 08, 2007 11:34 pm
- Location: Texas, Waxahachie
Yeah, I screwed up. It is the two speedo lights that are rigged, oops. I noticed both of these bulbs were blown, blackened to be precise.
I guess I will just solder the two back to the one, gonna have to add wire thats missing.
Here is a stupid question, I gave all the guage needles a light coat of red paint, they were pretty faded. This shouldnt throw off the readings, right? Not that they are pinpoint precise to begin with, but hopefully the added weight doesnt throw off the balance.
I guess I will just solder the two back to the one, gonna have to add wire thats missing.
Here is a stupid question, I gave all the guage needles a light coat of red paint, they were pretty faded. This shouldnt throw off the readings, right? Not that they are pinpoint precise to begin with, but hopefully the added weight doesnt throw off the balance.