Bezel tool

fordman · Post by **fordman** » Thu Jan 03, 2008 5:50 pm

yeah i just bought it out from under you.

i was just kidding. i think it will work. it is over 3 inches long. that should be enough to go over our knob studs.

kaptnkaos · Post by **kaptnkaos** » Thu Jan 03, 2008 6:11 pm

Hey Supermike...

Thanks for the post...

I just bought one of them... no worries mate there are still 3 left.
I've been looking for one like that and hadn't seen any.

That's a good price too...

Thanks agian

KaptnKA

S

l1k2gadd · Post by **l1k2gadd** » Thu Jan 03, 2008 7:00 pm

303 Stainless, is that a hardenend stainless? Is there such a thing?

I know 18-8 Stainless is the stainless steel that doesn't rust because I bought a bunch of threaded studs, nuts and washers for some Hurricane protection boards I had installed on one of my former homes here in Florida. The studs were screwed into tamp-in lead anchors in the block walls and were left there after fitting and removing the boards from the doors and windows. After 6 years, when I was moving out, they didn't show a bit of rust on them.

Isn't stainless is a soft metal that will break or bend easily when torqued on a lot?

seattle67 · Post by **seattle67** » Thu Jan 03, 2008 8:55 pm

This, of course, is completely from memory

Grade 303 Stainless steel represents superior machinability over all other austenitic stainless steels due to the addition of sulphur in the material.

The sulphur however, does reduce the materialâ€™s resistance to corrosion as well as causing poor weldability results.

The uses of grade 303 are as follows:

Â·Nuts & bolts
Â·Bushings
Â·Shafts
Â·Aircraft fittings
Â·Electrical switchgear components
Â·Gears

l1k2gadd · Post by **l1k2gadd** » Thu Jan 03, 2008 11:35 pm

Thanks.

Supermike · Post by **Supermike** » Fri Jan 04, 2008 12:28 am

Dang... you suckers are fast!! There were 4 available when I posted this, and then I went and ate dinner, put the kids to bed, and watched a TV show. I checked back just now, and there was only one left!! There have been 4 available for days... haha! I guess I helped them sell 'em... wonder if I can get a cut?

Anyhow... went ahead and bought the last one before one of you jokers grabbed it out from under me.

(hope it works, or the last laugh is on me!

)

kaptnkaos · Post by **kaptnkaos** » Fri Jan 04, 2008 12:47 am

Hey Super Mike

KaptnKA

S

basketcase0302 · Post by **basketcase0302** » Fri Jan 04, 2008 6:33 am

Dang bunch of wolves!

I want one!

Basketcase

Thunderfoot · Post by **Thunderfoot** » Sat Jan 05, 2008 2:07 am

Basketcase. 10 more available!

http://cgi.ebay.com/ebaymotors/New-Dash ... 0195946804 Well, make that 9

I got one too.

Thanks for the heads up Supermike

nadams · Post by **nadams** » Sat Jan 05, 2008 2:44 am

Now it's eight. I knew there was a reason that I liked you guys!

Thanks for the tip!

mljjones67 · Post by **mljjones67** » Sat Jan 05, 2008 3:23 am

Now seven!!!! better hurry

basketcase0302 · Post by **basketcase0302** » Sat Jan 05, 2008 6:26 am

Now six left!

Sure glad I got up early this morning!

Basketcase

Post by **Ranchero50** » Sat Jan 05, 2008 7:16 am

That's a pretty good deal. He's making money, but not a killking considering the machine steps unless he's getting the material for free.

Jamie

Banjo · Post by **Banjo** » Sat Jan 05, 2008 12:06 pm

Yep, thanks for the tip, old Banjo now has one incoming!

nadams · Post by **nadams** » Sat Jan 05, 2008 2:37 pm

I was looking at the other items that he/she (I am as PC as you can be

) is selling. I think they must work at some machining plant and are doing a little side work or have a very expensive set up at home. Either way I am getting a bezel. Thanks again for the tip.

The FORDification.com Forums

Bezel tool

re: Bezel tool

re: Bezel tool

re: Bezel tool

re: Bezel tool

re: Bezel tool

re: Bezel tool

re: Bezel tool

re: Bezel tool

re: Bezel tool

re: Bezel tool