Center Console ?

[ford4x4fun]

I would like to know what people have used for a center console in there trucks with buckets My truck is also a stick, but any and all ideas would be extremely helpful.

Thanks

[6T7Merc]

Im planning on making my own, and possibly experimenting with fiberglass and then covering it the same carpet as on the floor.

[peanutman]

Jc whitney might have something or you may get at least some ideas.

[72stepside]

Here's mine, stuffed between seats from a mid 80's Crown Vic.



I used scrap lumber, sanded it smoothe, and covered with polyurethane.

It has two cup holders and the door is held on with a piano hinge. The shield for the gas tank is just more of the same wood. I put velcro on it to secure it to the truck just above the tank, to keep it from rattling. It rests on the floor at the bottom.

Good luck.

[BiggDogg]

That gas tank cover idea is a good one! I dig it! Never thought about doing that until now...

[ford4x4fun]

72 Stepside that looks really good Both ideas actually!

[mike68merc]

I'm contemplating using the stock console from a 79 Bronco. I shimmed it a little in the front so it sat level. It has a recessed area under the leading edge that is not noticeable, but unnecessary in our trucks. It screws to the floor with 4 screws & BIG washers. Fits Nicely between the seats, with a good usable amount of storage, & 2 cup holders!....Though the cup holders are kind of shallow & I'd probably have my drink spilled on the first turn...
I believe these were used in Full size broncos well into the mid 80's...? I've seen them in many colors; Red, Blue, Grey, Black, Tan. Locks with a FORD key. I removed the lock mechanism & will take it to a locksmith to see if he can key it to match the lock on the glove box door. These consoles are textured plastic & kind of resemble an IGLOO ice chest...If I DO use it, I will have it wrapped in Vinyl (or something) by the upholsterer to make it blend with the interior better.
I'm asking for trouble with this last bit, but I also found a console from an '80's DODGE Ramcharger. Looks VERY similar but with a few small differences; Cup holders slightly deeper, console slightly wider (still fits fit nicely), textured a little finer...but keyed as a MOPAR, so key's won't match.
Any way, just an idea.

[ford4x4fun]

I like those seats mike... Where those the ones on ebay a few weeks back

[mike68merc]

Nope. Got em locally (Portland, OR) last year from a Gentleman (I use that term loosely!) who deals in used truck parts & specializes in our era of trucks. My truck came with buckets, but they were TRASHED! These came complete with bases & are in pretty nice shape... I replaced my ratty seats & bases with these....(then Craigslist-ed the junk ones for more than I paid for these.)
However they seem to be a little uncomfortable!?! I mocked up the interior when the truck was being disassembled. I sat in them for 5-10 minutes pretending to be Speed Racer, but haven't DRIVEN in them yet. My Girlfriend HATES them!! But I want to finish the truck & try them out for a wile. If they are uncomfortable, I'll find something else.....So the Jury is still out.

A funny thing...He said these were being used in the REAR seat section of a CREW CAB! He said the truck had TWO SETS of bucket seats & it looked to be FACTORY ORIGINAL....The factory reinforcements were under the cab.

****NOTE he sold me the seats from the rear, but used the mounting brackets from the front seats that were a little ratty. He said he sold the rear seat brackets for a small fortune.
I've never seen (or even heard of) such a thing. He seems to be a no BS kind of guy, so I trust he's not telling any fishing stories.
Just thought I'd share that & see what y'all thought...?

[ford4x4fun]

Well I haven't heard of that either they do look good though, I just got a set so I am hoping there not uncomfortable. I am still overseas so I haven't even got to sit in mine, but I am hoping they change the angle that I sit, so that my long legs aren't so uncomfortable driving down the road. Not that I am a giant guy but I am 5' 11" and 200 lbs and the angle really hurts the gas pedal leg (On Long Trips). So that is why I want to try the buckets! I think I am going to build my own center console, and cover it with Diamand Plate Aluminum, and trim the interior with that stuff as well. All in time though all I can do is sit here on my thoughts at the moment.

Nope. Got em locally (Portland, OR) last year from a Gentleman (I use that term loosely!) who deals in used truck parts & specializes in our era of trucks. My truck came with buckets, but they were TRASHED! These came complete with bases & are in pretty nice shape... I replaced my ratty seats & bases with these....(then Craigslist-ed the junk ones for more than I paid for these.)
However they seem to be a little uncomfortable!?! I mocked up the interior when the truck was being disassembled. I sat in them for 5-10 minutes pretending to be Speed Racer, but haven't DRIVEN in them yet. My Girlfriend HATES them!! But I want to finish the truck & try them out for a wile. If they are uncomfortable, I'll find something else.....So the Jury is still out.

A funny thing...He said these were being used in the REAR seat section of a CREW CAB! He said the truck had TWO SETS of bucket seats & it looked to be FACTORY ORIGINAL....The factory reinforcements were under the cab.

****NOTE he sold me the seats from the rear, but used the mounting brackets from the front seats that were a little ratty. He said he sold the rear seat brackets for a small fortune.
I've never seen (or even heard of) such a thing. He seems to be a no BS kind of guy, so I trust he's not telling any fishing stories.
Just thought I'd share that & see what y'all thought...?