What did you do to YOUR bump today?

[fitzwell]

disassembled the tilt column i got out of one the donor trucks in the country. Got a buddy of mine to order the bearings, retainers, etc. Slowly the pieces for my short bed are lining up.

[67F110]

Scrubbed prolly 20 years of dirt, moss and lichen off some seriously faded paint (this truck was last registered in 1980). Found a rust spot I didn't know existed at the rear corner of the cab. Managed to remove the completely corroded/frozen headlight switch without buggering up the dash paint. Plugged in a near perfect cigar lighter harvested at the U-Pull. Made plans for Sunday to pick up a bed off a '70 Ranger so she'll finally have something behind the cab.

[wt4speed#2]

disassembled the tilt column i got out of one the donor trucks in the country. Got a buddy of mine to order the bearings, retainers, etc. Slowly the pieces for my short bed are lining up.

We need to get together and compare column notes.Still carrying that header around in my back seat. Came in friday nite and laided down and died(hence no call ). Not going bacK to OKC till monday. Might take the good looking part of my group out to scoot a boot this friday nite(god knows she deserves it). But we got the grandbaby all day saturday while the kids move, you need to come by folr a bit.

[mikeconner1]

took the grille, & radiator off my 68, took the top panel off the grille. drilled some index holes in the hood hinge mountings, and disassembled the left door. Hope to get the interior out this week and get the inside and door jambs prepped to paint.

[fitzwell]

disassembled the tilt column i got out of one the donor trucks in the country. Got a buddy of mine to order the bearings, retainers, etc. Slowly the pieces for my short bed are lining up.

We need to get together and compare column notes.Still carrying that header around in my back seat. Came in friday nite and laided down and died(hence no call ). Not going bacK to OKC till monday. Might take the good looking part of my group out to scoot a boot this friday nite(god knows she deserves it). But we got the grandbaby all day saturday while the kids move, you need to come by folr a bit.

holler at me sat morning. Got an early parts run, but should be back on the westside about 10:30 or so...

[Off The Jeep End]

Got my new to me rear window installed

[austin]

fired her up and let her idel for a bit

[68_250]

Full tune up. Points and ignition stuff. Checked oil pressure and am going to replace sending unit on Saturday.
It shot and humid here right now.

[hotrod ford]

installed a new hood, fenders, bed and doors.

[Wes]

Fixed the brake light switch, got under the back and removed all the extra plug ins and wiring from P O. Rerouted and re-taped rear loom, fixed right tail light. Installed two halogen head lamps. Then went for a short drive.

[HillbillyDelux]

did some serious wash an wax then took it up the road an did a lil burnout haha gotta love it

[fordman]

i spent a whole 20 minutes at the junkyard. and i got my clip for my steering shaft. i got 2 of them. yes that other brand has and uses them. that is where i found both of them. one is the original stlye and the other is a differnt style but works the same.

[rjewkes]

Drove it into town for the first time in a month, all the rest have been start it and move it around the yard.

[1967AceStroker]

Took it cruising for a while, and did some... burnouts!

[mrsnicks]

Got the stupid lug nut lock off that I lost the key for. Cleaned up my back yard and put the fenders + inner fenders I had stored under the deck in the back of the truck. Home appraiser coming tomorrow. This weekend I WILL get that leaky wheel cylinder replaced.

Patrick