Parting out a truck, most parts available, SoCal

[jamiebennett]

hi do you have any other long bump side beds 67 to 69. looking for a clean rust free one. thanks jamie

[Calfdemon]

This is the only bed I have, but it is now available to whoever wants it as the original member that showed interest has not gotten back to me.

[jamiebennett]

sorry i think i will have to pass on this one

[sargentrs]

Do you happen to have the '68-'69 style inside door panels? The kind that don't have vinyl covers on 'em?

[habu]

Hey it's Brian,
Earlier you mentioned the fuel gauge selector switch, do you have it and the bezel or did I read that wrong.

Do you also have a passenger side inner fenderwell. When the muffler shop put on the headers they had to cut up the fender well to extract the 4 broken bolts on the passenger side.

If not I understand. If you do have 'em I can travel back out next weekend I believe.

Thanks again for the doors, likely to hang 'em next weekend. This weekend I spent doing motor stuff. So cannot wait to get the engine built and in.

Thank You,
Brian

[Calfdemon]

Do you happen to have the '68-'69 style inside door panels? The kind that don't have vinyl covers on 'em?

Hey Randy, I have a couple sets of those door panels, one set is uncut and the other 2 are both cut with speaker holes. One of the cut sets has the trim, the other doesnt. The uncut set also does not have trim. Let me know what you might be interested in and I can get some photos for you.

Hey it's Brian,
Earlier you mentioned the fuel gauge selector switch, do you have it and the bezel or did I read that wrong.

Do you also have a passenger side inner fenderwell. When the muffler shop put on the headers they had to cut up the fender well to extract the 4 broken bolts on the passenger side.

If not I understand. If you do have 'em I can travel back out next weekend I believe.

Thanks again for the doors, likely to hang 'em next weekend. This weekend I spent doing motor stuff. So cannot wait to get the engine built and in.

Thank You,
Brian

Hey Brian, I have both the tank selector switch, and the fuel gauge selector switch with bezel. I also have inner fenders. The passenger side inner fender has some rot under the battery tray but other than that, I believe it is solid everywhere else. When I can get back over there, I can take some photos for you if you want.

[habu]

That would be great if you could. I'll take the selector switch and bezel 'cause I'm using a cheapo pep-boys special now. Might be able to get up there this weekend or next for the inner fender.

Thanks Again I really appreciate it.
Brian

[Calfdemon]

I updated the first few posts with what has sold but I still have plenty left. As of right now, I have sales pending on the cab, the last set of doors, one of the bench seats (still one left), and the 9" rear end. If any of those sales fall through, then I will put them back up here for sale.

Off the top of my head, what I still have lying around and for sale is the 67 long bed, pair of front fenders, NP435 4 speed transmission, 1 bench seat, 1 in cab gas tank, the 2nd factory frame gas tank with skid plate and mounting brackets, front end suspension and steering components, 1 manual steering box, FE exhaust manifolds, many many many glove box doors, ash trays, and numerous other small items...

I have an extra 70-72 hood and a great tailgate too, but I am holding on to those as I am not sure whether I will be using them or not yet. Let me know if you need anything, especially smaller components, as I may have them sitting around and available for purchase. Everything is priced pretty cheap as I am just looking to break even on this parts truck and do not want to see any of these old bump parts go to waste.

Again, I do not want to ship any of the larger heavier items, but I will ship the small stuff.

[19alicia71]

Calfdemon,,,you have any front blinker lens off the 70-72 laying around mine are shot...? PM me if you do...and thanks again for the bezel.

Ken,

[Calfdemon]

Hey Ken, I will have to check. I believe I might have an extra pair sitting around somewhere in my garage. Ill check this weekend and see if I can find them.

[Chickenhawk368]

How much for the exaust manifolds?

[burkhart1202]

Do you have a radiator housing?

[Calfdemon]

How much for the exaust manifolds?

PM sent...

Do you have a radiator housing?

Do you mean the radiator support? I have one for a standard bumpside radiator (not super cooler), but I think it might have just a little rot on it. I will check it out today and get some pictures of where I think there might be a problem area. It is on the passenger side near the inner fender location. I believe the truck had a serious battery issue at one time as the inner fender on that side was rotted through where the battery went, and some of that rot went towards the radiator support. Either way, I will check it out today and see if it is even worth trying to use again...

[Calfdemon]

In the last 2 days, I have sold the cab, the doors, 1 bench seat, the front fenders, the inner fenders, the radiator support, the NP435 transmission, the drive shaft, the exhaust, the 9 inch rear, and a handful of other parts.

At this point, I still have the bed available for local pickup, 2 front chrome bumpers with very minor bends, an in cab gas tank, and 1 bench seat. I have numerous smaller interior parts available as well which I can ship. So I am just about done parting this thing out, but still have some stuff available. Hit me up if you need anything and I will see what I can do.

[jerrryhumpjr]

Do you still have any of the metal instrument clusters? Gauges/lights not important, as I will cut up to fab something similar to a F600/700. PM me with a price shipped to 28052, or UPS collect will be OK. Payment ???