clutch rod grommet
Moderator: FORDification
-
jimmy828
- 100% FORDified!
- Posts: 1611
- Joined: Thu Dec 23, 2010 6:47 pm
- Location: asheville,NC
clutch rod grommet
I have purchased a new grommet for the clutch rod. It has a metal flange with it but i do not know if the rubber/flange goes on top of carpet or below. When i took the old one out there was no carpet or matt.
You do not have the required permissions to view the files attached to this post.
-
sargentrs
- 100% FORDified!
- Posts: 9866
- Joined: Fri Jun 22, 2007 9:30 am
- Location: Georgia, Jasper
Re: clutch rod grommet
It's a seal so under the carpet, straight to the floor. Cut a hole in the carpet, just big enough so the carpet lays flat with the rubber tube sticking up through the carpet.
Randy
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
-
jimmy828
- 100% FORDified!
- Posts: 1611
- Joined: Thu Dec 23, 2010 6:47 pm
- Location: asheville,NC
Re: clutch rod grommet
Thanks Sarge. I thought that was the way it went. I wish there was a grommet or some kind of stitched hole in the carpet to make it look better. I hope there is a cure for that.sargentrs wrote:It's a seal so under the carpet, straight to the floor. Cut a hole in the carpet, just big enough so the carpet lays flat with the rubber tube sticking up through the carpet.
-
sargentrs
- 100% FORDified!
- Posts: 9866
- Joined: Fri Jun 22, 2007 9:30 am
- Location: Georgia, Jasper
Re: clutch rod grommet
If you had a 2nd metal plate you could make a "carpet sandwich" and cut out the carpet inside the oval?
Randy
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
1970 F100 Sport Custom Limited LWB, 302cid, 3 on the tree. NO A/C, NO P/S, NO P/B. Currently in 1000 pcs while rebuilding. Project thread: http://www.fordification.com/forum/view ... 22&t=59995 Plan: 351w, C4, LSD, pwr front disc, p/s, a/c, bucket seats, new interior and paint.
1987 F-150 XLT Lariat, 5.0/C6 auto.
-
jimmy828
- 100% FORDified!
- Posts: 1611
- Joined: Thu Dec 23, 2010 6:47 pm
- Location: asheville,NC
Re: clutch rod grommet
good idea. I'll let you know how that goes.sargentrs wrote:If you had a 2nd metal plate you could make a "carpet sandwich" and cut out the carpet inside the oval?